QNAP snapshots are block-based and only record the changed data.
If a file is accidentally deleted or modified, you can use snapshots to quickly restore the file to its previously-recorded state. Snapshots help protect your data by fully recording the NAS system state and metadata. Intel® Core™ i7-4770 3.40GHz CPU DDR3L 1600Hz 16GB WD 1TB WD10EZEX Intel Gigabit CT (MTU 1500) Windows® 10 64-bit Volume: RAID 5 4 x Intel S3500 240GB SSDs (SSDSC2BB240G4) QNAP LAN-10G2SF-MLX 2 ports 10GbE SFP+
VLC STREAMER ON QNAP FULL
The TS-253Be features Intel® AES-NI hardware-accelerated encryption to drive transfer speeds of up to 225 MB/s with AES 256-bit encryption for both full NAS volumes and shared folders, boosting system performance while ensuring the security of sensitive data stored in the TS-253Be. Powered by an Intel® Celeron® J3455 quad-core 1.5GHz processor (burst up to 2.3 GHz), 2GB/4GB DDR3L RAM (up to 8GB), dual Gigabit LAN ports, and supporting SATA 6Gb/s hard drives, the TS-253Be provides dependable performance of up to 225 MB/s read/write speeds. Intel® Celeron® J3455 quad-core 1.5GHz CPU with AES-NI Encryption QNAP QWA-AC2600), or boost the USB connectivity of the TS-253Be by installing a USB 3.1 10Gbps card.
VLC STREAMER ON QNAP INSTALL
Install a QNAP QM2 card to provide M.2 SSD caching/10GbE connectivity, or use the TS-253Be as a wireless access point by installing a compatible wireless network card (ex. With PCIe expansion, the TS-253Be provides flexibility in extending NAS functionality and potential applications. My understanding is that with NVR turned off in the app (which should then turn it off on the camera) I shouldn't be able to access the camera, but I can.Extend NAS functionalities with the PCIe slot
In QNAP Surveillance Station and in ONVIF Device Manager, the camera was still detected. Then I did the following - in the iOS YOOSEE app, I disabled the NVR connection. I can control the PTZ but not get a picture. If I follow the same steps as above, but not logged in to the ONVIF Device Manager application with the camera's credentials and I have the exact same experience. So I am connecting to the camera because I can control the lens position motor, but I can't get a picture/signal.
If I try to go to "Live video" link I get a "NO SIGNAL" message.If I click on the camera in the device list, I can connect to the camera.I logged in with my camera's admin/****** credentials.I have downloaded and installed the ONVIF Device Manager from to try to do some more troubleshooting.
VLC STREAMER ON QNAP PASSWORD
I tried again with the correct credentials and the stream opened, so the username and password are correct. VLC gave an error message that it couldn't connect. I wanted to confirm that the username assword credentials were correct so using VLC I opened the network stream without the username assword in the URL. I can connect to the camera and view the stream. I know the camera is working on my network because in VLC if I open a media stream with the RTSP address syntax you suggested above (i.e. Password: ******** Result: When I try to test this configuration I get the same error message "Failed to create the RTSP connection to the network camera." The same as in the screenshots from user "demos" above. Please check the RTSP port is correct and the RTSP streaming access name is 'live.sdp' on the network camera." RTSP Method Password: ******** Result: When I test I get an error "Failed to create the RTSP connection to the network camera. ONVIF MethodĬamera Model: ONVIF Cameras(Recording Only) I have tried to use both the ONVIF and the RTSP method. I have tried to set this camera up in QNAP Surveillance Station version 5.1.5.4.0 (9).
0 kommentar(er)
